Osram HTM 70

£5.80

SKU: 10281692 Category: Tags: , , , , ,

Description

Dimmer, Transformer, Led, Halogen, White

Osram HTM 70 properties

Product nameHTM 70
TypeDimmer
DimmerTransformer
Suitable for lamp typeHalogen, Led
Max Load Electronic transformers70 W
Min Load Electronic transformers20 W
Voltage240 V
ColourWhite
Height3.3 cm
Width5.2 cm
Depth10.8 cm
Weight110.0 g

Additional information

Product name

Product type

Dimmer

Suitable for lamp type

,

Voltage

Colour

Height

Width

Depth

Weight

Reviews

There are no reviews yet.

Be the first to review “Osram HTM 70”

Your email address will not be published. Required fields are marked *

Frequently Asked Questions:

Q: How do I properly install and set up my Osram HTM 70 LED light strip?

A: To properly install and set up your Osram HTM 70 LED light strip, follow these steps:

1. **Gather all necessary tools and materials**: You will need a measuring tape or ruler, a pen or pencil, scissors or a cutting tool, adhesive backing cutter (included in the package), a screwdriver or drill, and a power source with an appropriate voltage for your LED strip.

2. **Measure and mark**: Determine the desired length of your LED strip by measuring the area where you want to install it. Mark the starting point on both ends of the area using a pen or pencil.

3. **Unroll the LED strip**: Unwrap the LED strip from its packaging and lay it flat on a clean, dust-free surface. Carefully peel off the adhesive backing cover while avoiding contact with the adhesive tape to ensure proper adhesion later on.

4. **Cut the LED strip**: If necessary, cut the LED strip using scissors or a cutting tool according to your measured length. Ensure that you maintain an even cut for optimal performance. Remember not to cut individual LEDs as this will affect the light output and cause damage.

5. **Remove the adhesive backing**: Remove the protective film from both ends of the exposed adhesive tape on the backside of the LED strip. Take care not to touch or smudge the adhesive tape itself, as this may reduce its stickiness when applied.

6. **Install the LED strip**: Align the marked starting points with the LED strip's beginning and endpoints. Carefully press down on the adhesive tape to securely attach the strip along the desired area. Apply even pressure while avoiding any creases or wrinkles in the strip.

7. **Powering the LED strip**: Connect one end of an appropriate power cable (included in the package) to the LED strip's connector. Run the other end of the cable through a nearby electrical outlet or power source with matching voltage requirements. If using a smart plug or switch, follow manufacturer instructions for installation.

8. **Test and adjust**: Turn on your power source to test if the LED strip is functioning correctly. Adjust its brightness, color temperature, or other settings according to your preferences by using any compatible remote control, smartphone app, or wall-mounted controller provided with your purchase.

9. **Secure connections**: If necessary, use cable clips or adhesive hooks to keep the cables in place and ensure safety while preventing tripping hazards.

By following these steps, you can successfully install and set up your Osram HTM 70 LED light strip for optimal performance and enjoyment!

"How do I properly install the Osram HTM 70 lighting fixture, and what tools will be required?"

The installation of the Osram HTM 70 lighting fixture is a simple process that can be done by following these steps:

1. Gather the necessary tools: You will need a screwdriver, pliers, wire cutters, and a voltage tester. Turn off power: Before beginning any electrical work, turn off the power to the area where you will be installing the fixture at the circuit breaker or fuse box. Use the voltage tester to ensure there is no power flowing to the wiring. Remove the old fixture: Unscrew and remove the mounting bracket of the old fixture from the ceiling or wall. Disconnect the wires by gently pulling them apart. Label the wires according to their functions, such as black for hot, white for neutral, and green for ground. Install the new mounting bracket: Attach the provided mounting bracket to the electrical box using screws. If necessary, secure the bracket with plastic wire caps and twist ties. Make sure that the bracket is level and properly aligned. Connect the wiring: Strip approximately ½ inch of insulation from the ends of the wires. Connect the black wire from the fixture to the black wire from the house wiring, using wire nuts. Twist together the white wires and green grounding wires, again using wire nuts. Mount the fixture: Carefully lower the fixture onto the mounting bracket, making sure that it is level and centered. Tighten the screws to secure it in place. Attach the cover plate: Place the cover plate over the electrical box and attach it using screws. Make sure that it fits snugly around the edges of the fixture. Test the power: Turn the power back on at the circuit breaker or fuse box. Use the voltage tester to ensure that the wiring is working properly. By following these steps, you should be able to successfully install your new Osram HTM 70 lighting fixture. Remember to always take safety precautions when dealing with electrical work. If you are unsure about any of these steps, or if you encounter any difficulties during the installation process, it may be best to consult a licensed electrician for assistance.

"How do I properly install an Osram HTM 70 bulb in my headlight assembly?"

Turn off your car's engine and ensure that the parking brake is engaged. Open the hood of your car and locate the headlight assembly. The assembly may be mounted on a bracket or secured by screws or bolts, depending on your specific car model. Remove the old bulb by gently pulling it outwards. Be careful not to touch the glass surface of the bulb, as this can leave an oily residue that can affect its performance. If you need to handle the bulb, use a pair of gloves or clean, lint-free cloths to avoid contact with your skin. Clean the socket and surrounding area using a soft cloth and a small amount of alcohol or a specialized bulb cleaning solution. Be sure to remove any dirt, dust, or debris that may have accumulated around the socket. Insert the new Osram HTM 70 bulb into the socket, making sure that it is properly aligned and seated securely. The bulb should click into place once it is correctly installed. Replace any covers, brackets, or screws you removed earlier to secure the headlight assembly back in place. Close your car's hood and start your engine. Check that both headlights are functioning properly by switching on the headlights and driving at night or in a dimly lit area. Make sure that the bulbs produce the same level of brightness and don't have any visible flickering, shadows, or discoloration. If everything looks good, you can drive your car with confidence, knowing that your Osram HTM 70 bulb is providing optimal performance and illumination for safer driving in low-light conditions. Remember to follow the recommended service intervals provided by your car's manufacturer to ensure that your headlights continue to operate at peak efficiency over time.