Goobay 57195 100m

$31.99

Description

Power Cable, No, Black, Shielded

Goobay 57195 100m properties

Product name57195 100m
TypePower Cable
FeaturesShielded
GroundedNo
Cable Length100.0 m
ColourBlack
Weight3706.0 g

Additional information

Product name

Product type

Features

Grounded

Cable Length

Colour

Weight

Reviews

There are no reviews yet.

Be the first to review “Goobay 57195 100m”

Your email address will not be published. Required fields are marked *

Frequently Asked Questions:

How do I properly install the Goobay 57195 100m cable connector in an electrical system?

To install the Goobay 57195 100m cable connector in an electrical system, follow these steps:

1. Clean the connection points: Make sure that both the connector and the cable have clean contact surfaces. Use a dry cloth to wipe any dirt or debris off the connectors. Insert the cable: Insert one end of the cable into the connector. Ensure that the cable is properly seated in the connector. Connect the other end: Connect the other end of the cable to the corresponding connector on the electrical system. Make sure that both connectors are securely fastened. Test the connection: Check if the connection is stable by sending a signal through the cable. If there is no interference or distortion, then the installation is successful. Label the connector: To avoid confusion, label the connector with its corresponding location and function. Perform regular maintenance: Inspect the connectors periodically to ensure that they are still functioning properly. Replace any damaged connectors or cables immediately. Remember, always perform electrical work in accordance with local codes and safety guidelines. If you're unsure about anything, consult a licensed electrician for assistance.

"How do I properly install a new electrical outlet in my home using Goobay 57195 100m?"

To properly install a new electrical outlet in your home using Goobay 57195 100m, follow these steps:

1. Turn off power to the circuit you will be working on by flipping the corresponding circuit breaker switch or removing the fuse from the panel. Use a voltage tester to confirm that there is no electrical current flowing through the wires before proceeding with any work. Remove the existing outlet cover plate and pull out the old electrical outlet. Disconnect the wires from the back of the outlet, making note of which wire is connected to which screw terminal (usually white is neutral and goes to the silver or bronze screws, black or red is hot and goes to the gold or brass screw). Strip about 1/2 inch of insulation from the ends of the wires using a wire stripper tool. This will expose enough copper for connecting to the new outlet's screw terminals. Attach the mounting bracket that comes with the Goobay 57195 100m to the electrical box using the supplied screws. Make sure it is centered and level. Carefully feed the wires through the new outlet's entry slot, making sure the white wire goes to the left and the hot wire goes to the right (following the markings on the bracket). Gently bend the tabs inside the outlet to secure the wires in place. Connect each wire to the appropriate screw terminal on the new outlet. Use a pair of pliers to gently tighten the screws, but do not overtighten as this can cause damage to the wires or the outlet's internal components. Push the new electrical outlet into the electrical box and secure it in place using the supplied screws. Attach the cover plate over the top of the outlet. Turn the power back on at the circuit breaker or replace the fuse to restore electrical flow through the new outlet. Test the outlet with a plug-in tester to ensure proper functionality. If desired, use a decorative cover plate to further conceal and protect the newly installed outlet. Remember to always follow all safety precautions when working with electricity, including using appropriate tools and equipment, wearing protective clothing and gloves, and avoiding contact with live wires or electrical components.

How do I properly install a Goobay 57195 100m cable in my electrical system?

To properly install a Goobay 57195 100m cable in your electrical system, follow these steps:

1. Ensure that the power supply to the area where you will be installing the cable is turned off to avoid any electrical hazards. Prepare the route for the cable by ensuring that it is not obstructed or exposed to any sources of heat or moisture. Make sure the route is clear and secure, and that there are no sharp edges or corners that could damage the cable. Strip the ends of the cable using a cable stripper tool. Remove approximately 25mm (1 inch) of insulation from each end of the cable. Connect one end of the cable to your electrical device, following the manufacturer's instructions carefully. Make sure that the connectors are properly aligned and securely locked in place. Pull the cable through the prepared route, making sure it is not twisted or damaged. Avoid pulling too hard, as this could damage the cable or the connectors. Connect the other end of the cable to your power source, again following the manufacturer's instructions carefully. Make sure that the connectors are properly aligned and securely locked in place. Turn on the power supply and test the electrical device to ensure that it is functioning correctly. Label each end of the cable clearly, using a permanent marker or labeling tape, so that you can easily identify the device at either end. Ensure that the cable is properly secured and protected from any sources of damage or wear. This may involve using cable ties, cable clamps, or other protective devices, depending on the specific requirements of your electrical system. Regularly inspect the cable for any signs of damage, wear, or faults, and replace it immediately if any issues are identified. Proper maintenance and replacement of cables will help to ensure that your electrical system remains safe and reliable over time.