Frequently Asked Questions:

"How do I connect my Ideal Logic+ Heat H15 to the central heating system in my house?"

To connect your Ideal Logic+ Heat H15 boiler to the central heating system in your home, follow these steps:

1. Firstly, ensure that the power supply to your Ideal Logic+ Heat H15 is switched off at the consumer unit (fuse box). Next, turn off the water supply to the system by closing the filling link valve on the feed and expansion tank. This will prevent any further water entering the system whilst it is being worked on. Disconnect the existing boiler from the central heating system by releasing the connections between the boiler and radiators/heat emitters using a spanner or wrench. Be careful not to over tighten these connections, as this could damage the fittings. Remove the casing around the flue of your old boiler to expose the flue pipe. Using a hacksaw or pipe cutter, cut the flue pipe at the appropriate length to suit your requirements (ensuring that it is still above the roofline). Install the new Ideal Logic+ Heat H15 in the same location as the old boiler. This will help to ensure a quick and seamless installation process. Connect the flue pipe from the Ideal Logic+ Heat H15 to the existing chimney or flue using suitable fittings (such as a flexible aluminium connector). Make sure that these connections are securely tightened, but do not over-tighten them as this could damage the fittings. Connect the new Ideal Logic+ Heat H15 to the central heating system by attaching it to the existing radiators and heat emitters using the same connections that were used for your old boiler. Again, be careful not to over tighten these connections. Once all of the connections have been made, turn on the water supply to the system and switch on the power supply to the Ideal Logic+ Heat H15 at the consumer unit (fuse box). The boiler will now begin to fill with water. Monitor the pressure gauge on the front of the boiler, and use a pressure relief valve to release any excess pressure if necessary. Once the system has reached the correct operating pressure (usually around 1 bar), you can adjust the settings on your Ideal Logic+ Heat H15 to suit your preferences. This may include setting the temperature of the radiators, configuring the hot water delivery, and customising the boiler's output levels. Congratulations! Your new Ideal Logic+ Heat H15 is now connected to your central heating system and ready to use. Enjoy the benefits of increased energy efficiency, reduced running costs, and improved reliability that come with this top-of-the-line boiler.

"How do I set up my Ideal Logic+ Heat H15 for the first time?"

To set up your Ideal Logic+ Heat H15 boiler for the first time, follow these steps:

1. Before you begin, make sure that all necessary materials are present, including a wiring diagram, a voltage tester, and PVC pipes and fittings. Turn off the power supply to the boiler by switching off the circuit breaker in your electrical panel. Remove the boiler's access cover using a screwdriver and set it aside. Connect the wiring harness to the control board according to the wiring diagram provided. Use a voltage tester to ensure that there is no live voltage on the wires before touching them. Attach the flue outlet to the boiler's top section using screws and a sealant. Connect the chimney or flue pipe to the outlet. Install the bottom section of the boiler onto the floor, ensuring that it is level and securely fastened. Connect the cold water supply to the inlet valve on the side of the boiler using PVC pipes and fittings. Ensure a minimum 50mm clearance from any combustible surfaces. Attach the expansion vessel to the top section of the boiler, securing it with bolts and washers. Connect the expansion pipe between the expansion vessel and the system header tank. Install the pump onto the bottom section of the boiler, ensuring that it is aligned correctly. Connect the pump's electrical supply according to the wiring diagram. Fill the system with water using a hosepipe and a filling loop, making sure that the water level in the header tank reaches the correct height. Bleed any air from the radiators and the central heating system using a radiator bleed key. Turn on the power supply to the boiler by switching on the circuit breaker in your electrical panel. Run a series of tests, checking that the boiler is operating correctly and efficiently. This includes checking the water pressure, temperature, and flow rate. Make any necessary adjustments or calibrations to the system using the control board or programming interface. Test the system for leaks by running it at full capacity for a few hours. Check for any signs of dripping, condensation, or water damage. Ensure that the boiler and system are properly maintained and serviced on an annual basis to keep them operating efficiently and safely. By following these steps, you should be able to set up your Ideal Logic+ Heat H15 boiler for the first time with confidence. Remember always to follow safety guidelines and manufacturer instructions when working with any electrical or plumbing systems.

How to setup Ideal Logic+ Heat H15 heating boiler?

If you purchased your Ideal Logic+ Heat H15 heating boiler and are wondering how to optimize its operation so that it works ecologically and economically we invite you to read our article about the heating curve.

What is a heating effect of Ideal Logic+ Heat H15?

This gas boiler has the power of 15.0 kW. If your house is old-fashioned or lacks insulation, this boiler will be enough for 83 square meters of space. However, if your home is modern and insulated this boiler will be enough for 150 square meters of space. If your house is within this range, check also the other gas boilers in our offer, the power of which is 15.0 kW.