Jung 1224 LED UDE

$108.99

Description

Dimmer, Universal Dimmer, Transformer, Indoor, Led, Halogen, Incandescent, Touch, White, Black, Grey

Jung 1224 LED UDE properties

Product name1224 LED UDE
TypeDimmer
DimmerTransformer, Universal Dimmer
Suitable for lamp typeHalogen, Incandescent, Led
Area of UseIndoor
Max load Incandescent420 W
Min load Incandescent20 W
Max Load Led100 W
Min Load Led3 W
Max Load halogen420 W
Min Load halogen20 W
Max Load Electronic transformers420 W
Min Load Electronic transformers20 W
Rotating or TouchTouch
Voltage230 V
ColourBlack, Grey, White

Additional information

Product name

Product type

Dimmer

,

Suitable for lamp type

, ,

Area of Use

Max load Incandescent

Min load Incandescent

Max Load Led

Min Load Led

Max Load halogen

Min Load halogen

Rotating or Touch

Voltage

Colour

, ,

Reviews

There are no reviews yet.

Be the first to review “Jung 1224 LED UDE”

Your email address will not be published. Required fields are marked *

Frequently Asked Questions:

What is the recommended mounting method for installing the Jung 1224 LED UDE on a wall or surface?

The recommended mounting method for installing the Jung 1224 LED UDE on a wall or surface is by using a combination of screws and an adhesive tape. First, you'll need to attach the provided mounting bracket to the back of the fixture using the screws that come with it. Then, apply the adhesive tape (preferably double-sided VHB tape) on the wall or surface where you want to install the fixture. Next, align and press the mounted fixture onto the adhesive tape to secure it in place. Finally, make sure the fixture is firmly attached and leveled before turning it on.

Please note that the wall or surface must be clean, dry, and free of any dust or debris for the adhesive tape to work properly. Additionally, ensure that you have followed all safety precautions while handling tools and materials during the installation process.

How do I properly install and program the Jung 1224 LED UDE dimmer switch for use with LED lighting?

Here are the steps to follow for installing and programming a Jung 1224 LED UDE dimmer switch:

1. Before starting, ensure that the power supply is turned off at the circuit breaker or fuse box. Remove the existing wall plate cover and disconnect the wires from the old switch. Connect the black wire (usually the hot wire) from the new switch to the black wire in the electrical box, and connect the white wire (usually the neutral wire) from the new switch to the white wire in the electrical box using wire nuts. Strip the ends of the wires for about half an inch. If you have a 3-wire system with a green wire (usually the ground wire), connect it to the green screw on the side of the switch. Tighten the screws securely, but be careful not to overtighten and strip the wires. Mount the Jung 1224 LED UDE dimmer switch onto the electrical box using the supplied screws and wall plate cover. Make sure that the switch is level and properly aligned with the wall. Insert the batteries into the rear of the switch. The switch requires two AAA batteries (not included) for programming purposes. Turn on the power supply at the circuit breaker or fuse box, and press and hold the "PROG" button located near the bottom right corner of the switch. Keep holding the button until the LED indicator light flashes once. Release the button. Press the "+" key on the switch to increase the brightness level. The LED indicator light will flash twice as the dimmer level increments. Keep pressing the "+" key until you reach the desired brightness level. Press and hold the "PROG" button again, and release it when the LED indicator light flashes once. This saves your programming settings. If you want to reset the switch to factory settings, press and hold the "PROG" button for about 10 seconds until the LED indicator light starts blinking rapidly. Release the button, and then press the "PROG" button again to save the reset settings. Test the dimmer by turning it on and adjusting the brightness level using the "+" and "-" keys located near the bottom left corner of the switch. The LED indicator light will flash once as you adjust the dimmer level. By following these steps, your Jung 1224 LED UDE dimmer switch should be installed and programmed correctly for use with LED lighting. If you encounter any issues during the installation or programming process, consult the manufacturer's manual or contact a licensed electrician for assistance.